Difference between revisions of "User:Studenterhue/Sandbox"
Jump to navigation
Jump to search
Studenterhue (talk | contribs) |
Studenterhue (talk | contribs) |
||
| Line 8: | Line 8: | ||
===Harvesting Hotspots: The Easy Part=== | ===Harvesting Hotspots: The Easy Part=== | ||
Once you've finally found the center of the hotspot, everything afterwards is pretty easy. | |||
#Drag the stomper unit directly over the center of the hotspot or directly adjacent to it (i.e., usually where the rod reads 0 or 1). | |||
#Click on the stomper unit to lock the hotspot in place. Remember, hotspots occasionally move, so if you don't lock it, your vents will eventually lose heat and power. If you've correctly found the center, the stomper will beep out that the hotspot was successfully pinned. | |||
#Place some wire over the center, then click on the bit of wire created to place some wire on the square you're standing on. | |||
#Dig a hole in the hotspot center with the power shovel to make room for the vent unit. | |||
#Construct the vent capture unit. Thanks to imcoder magic, you can either: | |||
##Stand over the center of the hotspot and click on the unbuilt vent capture unit kit, as if you were constructing a table. | |||
##Plop the unit over the center and use a screwdriver or wrench on it. | |||
#Lay wire from the vent back to the station power grid. The safest practice is to connect it to the fork of wires just outside the [[Engineering#Oshan|Power Room]], but wiring it to the super-convenient cable line connecting the [[Research Outpost#Oshan|Research Outpost]] to the station or any random wire is usually fine, so long as the connected vent(s) isn't/aren't outputting too much electricity. | |||
#*Pro-tip: Click on the wire while it's in your hand to start laying down cable as you move. Now, instead of constantly stopping every tile to lay down cable, you can just mosey down back to [[Engineering#Oshan|Engineering]] | |||
===Boosting Power Generation=== | ===Boosting Power Generation=== | ||
---- | ---- | ||
Revision as of 05:15, 17 December 2018
Powering the station: the geothermal capture system
All about Hotspots
Essential Equipment & Machinery
Hunting for & Centering Hotspots: The Hard Part
Harvesting Hotspots: The Easy Part
Once you've finally found the center of the hotspot, everything afterwards is pretty easy.
- Drag the stomper unit directly over the center of the hotspot or directly adjacent to it (i.e., usually where the rod reads 0 or 1).
- Click on the stomper unit to lock the hotspot in place. Remember, hotspots occasionally move, so if you don't lock it, your vents will eventually lose heat and power. If you've correctly found the center, the stomper will beep out that the hotspot was successfully pinned.
- Place some wire over the center, then click on the bit of wire created to place some wire on the square you're standing on.
- Dig a hole in the hotspot center with the power shovel to make room for the vent unit.
- Construct the vent capture unit. Thanks to imcoder magic, you can either:
- Stand over the center of the hotspot and click on the unbuilt vent capture unit kit, as if you were constructing a table.
- Plop the unit over the center and use a screwdriver or wrench on it.
- Lay wire from the vent back to the station power grid. The safest practice is to connect it to the fork of wires just outside the Power Room, but wiring it to the super-convenient cable line connecting the Research Outpost to the station or any random wire is usually fine, so long as the connected vent(s) isn't/aren't outputting too much electricity.
- Pro-tip: Click on the wire while it's in your hand to start laying down cable as you move. Now, instead of constantly stopping every tile to lay down cable, you can just mosey down back to Engineering