User:Cherman0/Geothermal Generator

From Space Station 13 Wiki
< User:Cherman0
Revision as of 01:14, 15 November 2022 by Cherman0 (talk | contribs) (finished raising power)
Jump to navigation Jump to search

The Geothermal Engine is the main source of power on Oshan Laboratory. It generates power by tapping into the natural heat of tectonic hotspots on the ocean floor.

Parts of the Geothermal Engine

Hotspots

Locating and pinning hotspots and connecting vents from them to the power grid is the primary objective of the engineers running the engine on Oshan. At the beginning of the round, 43 hotspots are spread about the map, and their starting locations are visible by using the "Trench Map" button on all PDAs. These hotspots periodically move, which causes an earthquake where they are. These earthquakes will move dowsing rods along with the hotspot, allowing you to keep track of them as they move.

Dowsing Rod

DrowsingRod.png

Dowsing rods are used to locate the center of a hotspot for the purpose of pinning it down and building a capture vent on it. When you deploy a dowsing rod on the ground, it will beep and state a number if it is within a 10 tile radius of a hotspot. That number is an estimated distance to the center of the hotspot: if you deploy it somewhere else, the number will probably be bigger or smaller. However, it is not entirely accurate. The motion of a hotspot causes all of the tiles between its current location and next location to read as being zero tiles from the center. You can tell when youve found the true center of a hotspot because the dowsing rod will make a much higher-pitched beep when you place it on the correct tile. The image below illustrates the inaccuracy of dowsing rods (the red square is the true center, the arrow is the direction of motion):

An illustration of Doppler shift.

Stomper Unit

StomperUnit.png

Stomper units can be used to pin down a hotspot by stomping within a tile of its center. Pinned hotspots will no longer move or cause earthquakes. If you stomp outside of that range, the hotspot will quake and move away from the stomper, which can be used to slowly but deliberately move hotspots. When the stomper pins a hotspot, it will emit a beep and say that it pinned a hotspot.

Right clicking a stomper and selecting from the context menu will allow you to toggle it between single and automatic modes. In single mode it will only stomp once per activation, whereas in automatic mode it will continue stomping until activated again.

Engineering also has access to stomper boots, which can be worn and activated to stomp a hotspot. They slow you down immensely when worn, so if you plan on using them it is best to keep them in your bag until they are needed.

Geothermal Capture Vent

UnbuiltVentCaptureUnit.png

After pinning a hotspot in place, vents can be deployed to harvest electrical power from it. To deploy a vent, first use a Power Shovel to dig a hole where the hotspot was pinned. Then, simply click the hole with a vent capture unit in-hand (or drop the vent unit and click-and-drag its sprite onto the hole) to deploy it. Once deployed, it will need to be wired into the SMES units to get its power to the station grid.

The power output of a geothermal vent is dependent on the number of hotspots stacked on the same tile, the number of rocks that have been mined out from the trench under the hotspot, the number of vents on the hotspot, and the distance of the vent from the center of the hotspot.

Common Hazards

Earthquakes

As hotspots move, they cause earthquakes in their wake. The more powerful the hotspot is and the more of them that are in the same place, the more powerful the earthquake. With just one or two hotspots stacked on top of each other the threat is relatively minimal, but as the hotspot stack becomes more powerful the quakes can start to tear pits into the trench, deal heavy BRUTE damage, amputate limbs, and even outright gib people.

Trench Pits

Whether naturally occurring or caused by an earthquake, holes onto the trench may pose a hazard. Falling into one will cause medium BRUTE damage, but the real danger is being stuck with no good way out. Hostile creatures and syndicate drones make it a dangerous area, and if you don't have a dive suit you will take rapid BURN damage as well. Your power shovel can dig through basic rocks, meaning you may be able to make it to the sea elevator and catch a ride back to the station. Carrying a Sea Ladder will also allow you to climb back out of the trench in the event that you fall in a hole.

Oxygen

Obviously, you cannot breathe the ocean. Carrying an oxygen tank will be necessary for ocean excursions, and you will need to monitor its pressure in order to not be caught in a bad spot with no air left. It may be worth carrying a spare tank in your backpack for emergencies.

Basic Startup Procedure

  1. Grab any necessary equipment. Make sure to have a dowsing rod, stomper, power shovel, capture vent, and a box of wire. You will also need an oxygen supply and will greatly appreciate having flippers.
  2. Check the trench map on your PDA or sitting on the nearby tables to see where the hotspots spawned. The map will show the trench and not the station, so you will need to use some intuition to know where these spots correspond to on the station level. If all else fails, wandering about the ocean randomly placing dowsing rods will find a hotspot eventually.
  3. Scout the ocean for hotspots using dowsing rods. If you don't already know where a hotspot may be, this could take a little while. The dowsing rods will find any hotspots in a 10x10 radius, so if you don't get a hit then walk a bit aways and try again.
  4. Once you've located a hotspot and further located its center, use a stomper on it to pin it in place.
  5. Use a power shovel on the center of the hotspot to dig a hole there, and then use a capture vent on the hole to deploy it.
  6. Use a wire on the vent to lay a wire under it. Continue this wire to connect to the SMES units on-station.
  7. Set the SMES units to reasonable charge/discharge rates. Make sure not to set the SMESs to charge with more power then you actually generate, or they will not charge at all.

Raising Output

Hotspot Stacking

Having multiple hotspots pinned on the same tile will multiply all of their power outputs by (1 + number of hotspots / 2.3). Each hotspot causing a multiplication of all hotspot strengths causes output to scale exponentially with hotspot stack size.

Pinning multiple hotspots on one tile will require careful manipulation of the stomper ranges to move the new hotspot onto an existing tile without disturbing the existing pile. Stompers have the same range as dowsing rods detect from, so you will want to space the stomper so that you can move the new hotspot onto the stack without moving the stack itself.

Vent Stacking

Building multiple vents around a hotspot will reduce the output of any one vent, but will collectively yield more power than previously in most cases. Since vents give less power the farther they are from the center, it is optimal to build any new vents in a square formation around the center of the hotspot.

Undermining

Mining out the stone in the area of the trench under the hotspot will increase its power. You will know you are digging under a hotspot when the rocks emit sparks as they break. This will also increase the destructive power of the hotspot's earthquakes as it travels, so it is best to do any undermining after you've already locked it in its final position.